Monday, July 26, 2010

Travel Trailer

In mid June we decided to purchase a travel trailer as my wife no longer wanted to stay in a tent with our 3 year old and renting a RV would cost around $1100 for a week.  Well, we picked up a 1973 Lely Greman trailer that is 23' long.  There was some work that needed to get put into, but even with all that we have put into it as long as we use it twice we are still ahead of the game.

After sitting in it for a while without the pressure of people watching us inspect their trailer we noticed we had missed some things.  We initially thought that there had not been any water damage to the trailer, which would was quite impressive given it's age.  But as we started digging a little deeper and looking closer we noticed there was some, but there had been some craftsmen that have owned the trailer over the years and have repaired it nicely.  Also there have been some hack artists that have slapped something in quick or chopped things out.

This is especially evident with the tail light wiring.  As you can see in the pictures they screwed in two lights up at the top and ran the wiring up to the tongue of the trailer.  Along the way they spliced in random colors of wire when it wouldn't reach.  When they got to the front of the trailer they spliced in more wire to match the wiring colors of the 7 pin flat wiring connector.  To hold the wires in place they were aluminum duct taped to the trailer making it look very pleasing.  Now the trucks that I use are older and farm vehicles and use the 6 pin round connector so I thought that this would be an easy switch.  Armed with color wiring diagrams from various places on the Internet I took apart the plug and set to switch it to the one that I would use.  After trying various configurations in the plug I found it prudent to rip out everything and start again.  I reused the lights but mounted them just inside the existing tail lights.  I went and bought a run of 25' flat four wire, some split loom and some plastic cable clamps from Princess Auto and ran the wire underneath the trailer.  I made sure that when I ran the split loom I had the opening facing down in the low spots.  Under the trailer is quite interesting with many wires just abandoned from previous repairs.  Not knowing what was good and what was not I left it until future investigation.

When we removed the tape holding the wires onto the trailer it peeled the tape, as well from the pictures you can see some of the prolific stickers that adorned the trailer.  My wife removed all of these blemishes and armed with a gallon of Tremclad White and silicone she went about painting and sealing the trailer. 

The 12V system had been neglected sometime in the past as the previous owner had never used any of it.  There was no sign of where a battery was to go or a converter box was supposed to go.  I grew up with an old tent trailer of similar vintage and it had a converter box that converted 120V power to 12V power to run the lights and the water pump, or when AC power was not available you could run it off of a deep cycle battery.  This was a good set up from my memory and I would like to have that in my own trailer.  Luckily for me my in laws had a tent trailer that they were going to gut and I could salvage whatever I wanted from it.  So we popped it open found the converter box and removed it.  The power system in my trailer consisted of plugging into the main power which was breakered into two receptacles and a light that was unswitched. 

I went to NAPA and picked up a group 27 deep cycle batter, some 8 gauge wire, and a battery box and mounted it on the tongue of the trailer as I didn't want to have it inside for venting purposes.  I didn't need to drill a new hole, just pop out some old unused BX cable.  I hooked the battery into the converter box that I had installed into side of the bench.  From the panel I ran the positive to a distribution block where I have everything fused, and then out to the various items.  I wanted a nice clean grounding set up, so I wanted to get a common ground block found in AC electrical panels, but none of the vendors in Calgary stock those, but I was talking on the radio with a few guys and one from Bragg Creek had some left over from an old panel.  With that installed the converter, battery and all devices are now grounded.  Also, on the battery I put a 50A fuse just in case.

There were two water pumps in the trailer, one for the kitchen sink and one for the bathroom sink.  As I was moving wires around the kitchen sink pump's wire broke free of it's solder joint, that was all that needed to be repaired with that pump.  The bathroom pump wouldn't turn on, so I got the probes of my multimeter into some of the butt connectors and I measured a voltage across the switch, which meant the switch was malfunctioning.  After a trip to Canadian Tire for a SPST switch I was able to get that pump working.  I filled the water tank and shocked it with a little bit of bleach, because we don't know how long the tank has been empty and what may have lived in there during that time.



Upcoming items on trailer include:
- running wire for a car stereo and install one with some speaker
- running wire for a FT-2900 and install a 2m antenna
- replace furnace
- replace one of the 120V fixtures for a 12V fixture
- open up and repair the 12V spot light

The rear of the trailer.  See the dangling wires and the stickers.

Passenger side of the trailer.  More stickers and the tail light wires coming down the side.

No comments:

Post a Comment